Разлика између цилиндричног глодала и крајњег глодала

The helical-tooth coarse-tooth milling cutter has few teeth, high tooth strength, large chip space, and is suitable for rough machining. The fine-tooth milling cutter is suitable for finishing. Multiple milling cutters can be combined for wide-plane milling, and the left and right staggered spiral teeth must be combined.

Cylindrical milling cutters have high productivity. Milling cutters rotate continuously during milling and allow higher milling speeds, so they have higher productivity. During continuous cutting and milling, each tooth is continuously cutting, especially in end milling. The milling force fluctuates greatly, so vibration is unavoidable. When the frequency of the vibration is the same or multiple of the natural frequency of the machine tool, the vibration is the most serious.

In addition, when high-speed цнц глодање, the cutter teeth have to undergo periodic cold and hot impact, which is prone to cracks and chipping, which reduces the durability of the tool. Multi-tool multi-edge cutting milling cutters have many teeth and a large total cutting edge length, which is conducive to improving the durability and productivity of the tool, and has many advantages.

However, there are two problems in the following: one is that the cutter teeth are prone to radial runout, which will cause the cutter teeth to have unequal load and uneven wear, affecting the quality of the processed surface; the second is that the chip clearance space of the cutter teeth must be sufficient Otherwise it will damage the cutter teeth. Different milling methods According to different machining conditions, in order to improve the durability and productivity of the tool, you can choose different milling methods, such as upside down milling, down milling or symmetrical milling, asymmetric milling, etc.

In addition to cylindrical milling cutters, end milling cutters are also more commonly used. So, what is the difference between a cylindrical milling cutter and an end milling cutter? The most direct difference is that the cylindrical milling cutter is worn on the tool holder, and the end mill can be used by directly inserting it into the taper hole of the spindle. End mills are used to process grooves and stepped surfaces. The teeth are on the circumference and the end surface. Generally, the feed cannot be axially fed. When the end mill has teeth passing through the center end, it can feed axially.

In addition, the use range and requirements of high-speed steel end mills are relatively wide, and even if the choice of cutting conditions is slightly inappropriate, there will not be too many problems. Although hard alloy end mills have good wear resistance during high-speed cutting, they are not as widely used as high-speed steel end mills, and the cutting conditions must strictly meet the requirements of the tool.

Линк до овог чланка: Разлика између цилиндричног глодала и крајњег глодала

Изјава о поновном штампању: Ако нема посебних упутстава, сви чланци на овој страници су оригинални. Наведите извор за поновно штампање: хттпс: //ввв.цнцмацхинингптј.цом/，хвала！

ПТЈ® пружа читав низ прилагођених прецизности ЦНЦ обрада Кина услуге.Оверено ИСО 9001: 2015 и АС-9100. Брза прецизност 3, 4 и 5 оса ЦНЦ обрада услуге укључујући глодање, окретање према спецификацијама купца, могућност обраде делова од метала и пластике са толеранцијом +/- 0.005 мм. Секундарне услуге укључују ЦНЦ и конвенционално брушење, бушење,ливење на ливење,Лим жигосање.Пружање прототипова, комплетне производне серије, техничка подршка и потпуни преглед аутомобилски, ваздушно-космички простор, калупи и елементи, лед осветљење,медицински, бицикл и потрошач електроника индустрије. Правовремена достава.Реците нам мало о буџету вашег пројекта и очекиваном времену испоруке. Са вама ћемо припремити стратегију за пружање најисплативијих услуга које ће вам помоћи да постигнете свој циљ. Добродошли у контакт са нама ( салес@пинтејин.цом ) директно за ваш нови пројекат.